C shift

  I worked on PM’s today MP-6,11, & 19.

 

 I took the full waste oil drums on the spill pallet to the oil storage shed – will email Walter M. so he can have it picked up.

 

 I started vacuuming out the pan on press #1. The tank is low.

End of arm tooling cart.

Found an example of a good idea put to use. Why not keep components centralized?

MP#13- robot and press settings.

Had an issue where the pendant had probably been dropped and wires had pulled loose inside. After correcting the problem, many settings had been changed.

Including part drop detect on the press and robot were both turned on. The machine would cycle only once and stop because of this.

For future reference MD4 should be "on" for the robot not to look for part and "drop should be set to zero (off) on the press, NOT to look for part.

Sean 9/13/09

Press#3 Oil Leak

Pump started leaking, lost about 30 gallons of oil. There were 4 screws loose. Tightened it up, checked operation, O.k. to run.

Sean 9/11/09

Sprue Pickers

Printed off the manuals for the yushin pickers, I am finding a few problems as I go through them but picking out the best.

Collin and I put one on press#17 and Press#14 Friday night.

Press# 16 is next for a 550. Then I was going to put 900's on 18,19, and 20.

Ronnie said that press22 was going to move soon so we will hold off until then. (With a 750).

Building adapter plates as we go for now since each machine must be uniquely fit and are drilled different.

The interface schematics are on the table in the shop next to the good 120vac interface box.

Josh is supposed to be getting more in soon.

Sean 9/11/09

New Equipment Update

As you may already know, we bought some new equipment yesterday.  If you include the shipment of used sprue pickers, dryers, and blenders we got this week,  here is where we stand-  We have 7 sprue pickers, 3 mold machines, 5 robots (maybe 6), 3 dryers, 4 dryer/hopper/loader combos, 7 conveyor belts, and 2 blenders to get installed and running.  PLUS- keeping the floor running, Eagle and Pilot launches. The next few weeks and months should be pretty crazy around here.

This stuff won’t ship until the week of the 14^th.  Until then we need to be finishing Eagle and Pilot projects and working on new robot installations.  Once the new equipment gets here, priority shifts to getting the three new machines running with robots and support equipment.  Then we will focus on the remaining robot and aux. equipment installations.

OF THE SPRUE PICKERS WE GOT THIS WEEK-  Most of them are located in the storage trailer next to the pallet room.  I have 5 more pendants coming next week.  We need to pick out the best of the following sizes-  (3) 550 models, (2) 750 models, and (2) 900 models.  They will go on MP’s 14, 16, 17, 18, 19, 20, and 22.  Get them in the shop and de-bugged and then see what needs to be done to mount them on the machines.  We should probably save a couple of the remaining pickers for future use and rob spare parts off the others.  I will work on the machine interfaces.  We are going to need all the spare room we can for new stuff coming in.

Contact me with any questions.  Just dig in and I will keep all of you updated.

Thanks for all your efforts.

  Joshua Ledbetter

  Manufacturing Engineer

  Oreck Manufacturing Company

  931-239-3235

 

Water System

We cleaned the filter screens on all the presses tonight. They were very bad, I think this has been affecting thermolator performance.

Sean

Mezzanine room electrical.

What I thought was a bad breaker the other day turned out to be a burnt wire nut.

Tonight there was a repeat incident on the junction bux just up from it for dryers 8 and 9.

Might want to watch for that in the future.

Sean

MP4 Robot Stopping

What is causing MP4 to stop with the robot above the mold and the machine displaying “Eject Forward Permission Not Made” alarm is this-

When the clamp opens fast, the ejectors are drifting past the eject retract set point (Menu 41, Input 121).  The robot will not go into the mold without this input.  We will repair the drifting problem asap, but in the meanwhile, make sure your retract set point is back far enough to compensate for this.

Thanks

 

  Joshua Ledbetter

  Manufacturing Engineer

  Oreck Manufacturing Company

  931-239-3235

 

DR-7 Breaker out in Mezz room.

The Breaker needs replaced in Panel DH1, could not locate a 20 Amp. I will check with Mark or Gary to see if they know where one is.

Sean

D-shift core problems on #10.

Had some problems with the core set switch not reading correctly.

The symptom was that the set switch would not make at first try in manual, but, when you set it the second time it would make.

I went through checking for loose connections, replaced the switch, and the relay module (110vac), but no change.

We found that pressure was only 500psi.

Although no adjustments had been done on press#10, we adjusted V225 pressure relief valve to 1550 and had no further problems.

This is interesting because the press was running when the fault occurred.

Sean

Phone post test

"C" Shift

  Well, they jammed another grinder with santoprene . I spent 2 hours disassembling the grinder. It’s going to take awhile to clean this one out.

 

 I spent most of the rest of the day trying to finish up PMs.

 

                                                                                                                                             

             

 

 

                                                                                                                                                             R. Upchurch

                                                                                                                                                             C - Shift

Another test

I entered my profile info into the google blogger so my name should automatically appear now when I make a posting.

 

Sean Kearns

Maintenance Technician

Oreck manufacturing Company

931-239-7671

 

Posting Instructions

Whenever you post by sending an email to log@moldingsupport.com, be sure to put your name at the end of the message. Whenever anyone of us posts to this site it automatically assumes we are the same person for some reason and I have yet to figure out how to make it show the sent from email address.
Also, if anyone is interested I can also set up your cell phone where you can easily post to this site by sending a text message to 256447 (BLOGGR). It will post your message just as it would an email to the log address.
Thanks
Josh

test

Hey guys,

                Just trying out the new blog--------

 

  There’s not a lot  going on today, just trying to get PMs done.

 

                                                            Later………………….

Start Posting

Test email to log@moldingsupport.com

Josh